• THERMOPLASTIC INDUSTRIAL & PTFE HOSES

The thermoplastic industrial hoses are made of a polyester elastomer substrate, a reinforcement of 1/2 synthetic fiber braids and a polyurethane black, micro-perforated covering, with white or black ink-jet marking.

The PTFE hoses are reinforced by 2 stainless steel AISI 304 braids.

Applications: Forklift trucks, articulating and telescopic booms, aerial platforms, scissor lifts, cranes, general hydraulics, industrial gases.

• INDUSTRIAL HOSES FOR HIGH PRESSURE & TEMPERATURE

The Industrial hoses for high pressure & temperature are internally made of oil resistant synthetic rubber and reinforced with a high tensile steel wire braid. The external cover made of synthetic rubber is very resistant to abrasion, weather, ozone, oil and high temperature.

Applications: Hydraulic mineral and “biological” oils, polyglycol base oils, water, oil/water emulsions. Note: for medium-high pressure lines at very high temperature. Temperature range: -40°/+135° with peak of +150°

• INSULATING HOSES

The inner tube of the insulating hoses is made of white smooth EPDM rubber, electrically isolated, suitable for high temperature. Reinforcement: synthetic high strength cord. The cover is made of Blue EPDM rubber, electrically isolated, abrasion resistant and suitable for high temperature and ozone resistance.

• HOSES FOR OXYGEN

Softwall hoses for oxygen delivery in the iron and steel industries, useful in all cases where a rubber hose is working close to sources of heat.

• HOSES FOR ABRASIVE MATERIALS

The hoses for abrasive materials are suitable for pneumatic conveying (suction and discharge) in industrial applications of dry cement, coal and RDF (refuse derived fuel from the recovery, synergistic to coal dust), minerals, ceramic powder, glass fiber and the load of tanks, and storage ware houses and silos.

Applications: steel mills, coking plants, power plants and factories of ceramic, glass, insulation materials, cement, etc.

• CABLE PROTECTION HOSES

The cable protection hoses are smooth, gray, made of EPDM rubber, reinforced with high-strength synthetic fabric with a black cover, wrapped finish, CR rubber. Applications: specifically designed as a protective sheath, water-cooling for the feeding cables in the EAF.

• FLEXIBLE STAINLESS STEEL HOSES – SINGLE OR DOUBLE BRAID

The flexible stainless steel hoses are at the top of a range of products studied for fluids crossing. The structure, completely in stainless steel, allows you to have a very good heat resistance (up to +700°C) and a very strong acids resistance. The available inside diameter is from 6 up to 250 mm.

The flexible stainless steel hoses are suitable for applications in various industries. The flexible INOX hoses can be welded to a lot of fittings and flanges available on the market, satisfying every customer request. They are available in single/double braid versions.

• INDUSTRIAL HOSES FOR HIGH PRESSURE / HYDRAULICS

The industrial hoses for high pressure / hydraulics are internally coated pipes with a synthetic rubber layer, reinforced with 2 braids of high tensile steel. The synthetic rubber has an excellent resistance to abrasion, ozone, oil and aging.

• RUBBER HOSES FOR WATER, STEAM AND ABRASIVES

The hoses for water are made of a synthetic rubber sub-layer. Reinforced with high-strength synthetic materials and covered with synthetic rubber, resistant to weather and ozone.

The hoses for steam are black EPDM rubber pipes. They are smooth and resistant to saturated steam. They are reinforced with high-strength synthetic fibers and covered with black, smooth EPDM rubber that is resistant to high temperature, weathering and ozone.

The wear resistant hoses have the following characteristics:

• Inner tube: Black, smooth, antistatic SBR/NR rubber, abrasion resistant.
• Reinforcement: High strength synthetic cord.
• Cover: Black, smooth, (wrapped finish) antistatic SBR/NR rubber, abrasion resistant.
• Applications: delivery and suction of sand or cast steel shot. Manufactured with antistatic rubber compound.

L'articolo Industrial hoses for various applications proviene da FORTEK.

The stainless steel expansion joints are mounted on pipes where it is necessary to absorb thermal expansion or vibration.

The stainless steel bellows is formed cold hydraulically so as not to alter the initial structure and the strength of the material.

The use of several, differently thick walls determines the main characteristics of the product: the axial stiffness and the maximum operating pressure.

Depending on the type of dilation that they can absorb, the compensators are classified as:

• axial
• universal
• angular
• spherical angular
• side
• spherical lateral
• axial thrust
• push universal

L'articolo Rubber and Stainless Steel expansion joints proviene da FORTEK.

The GEMÜ 1436 cPos® eco digital electro-pneumatic positioner, travel sensor, switching valves and status LEDs are integrated in a solid compact housing. Pneumatic and electrical connections are in one mounting direction to save space and enable easy access.

Features

• Simple use and operation
• Direct or remote positioner mounting to the process valve
• Can be used for single acting linear or quarter turn actuators
• Optimized initialisation and valve control

Advantages

• No air consumption when idle
• Simple mounting to various valve actuators

L'articolo Positioner and process controller GEMÜ 1436 cPos eco proviene da FORTEK.

SPECIFICATIONS

L'articolo VIKING Ammonia – Internal gear pumps proviene da FORTEK.

The Viking General Purpose Series 32 pumps possess excellent vacuum characteristics and will operate and prime at suction lifts up to 25 feet, depending upon the vaporization point of volatile liquids. Because of the cushioned action in providing a continuous and steady stream of liquid without splashing, pounding, foaming or churning, the Viking pump is adaptable to an unlimited number of industrial applications.

All sizes of Viking General Purpose pumps have tapped ports except “LQ”, “LL”, “Q”, “M” and “N” sizes. These have flanged ports ready to accept companion flanges. “K” through “N” sizes are furnished with conventional packing as standard. A cartridge style triple lip sealing option is available for the “K” through “N” sizes, contact the factory for details. A supporting anti-friction bearing pillow block is recommended for the end of the pump shaft on all V-belt driven units.

SPECIFICATIONS

L'articolo VIKING General purpose – Internal gear pumps proviene da FORTEK.

The GEN fire-fighting booster sets are built in conformity with EN12845 for automatic sprinkler systems and with UNI10779 for hydrant systems. In accordance with the above standards, all the main components of the booster set are factory connected and assembled. The configuration of the booster set depends on the number of pumps installed and on the type of electric motor or diesel engine, consistently with the type of supply chosen for the fire-fighting system from among those described in the standard.

The water supply can be single, superior, duplicated or combined. Two main service pumps, one backing up the other, are normally installed for fire-fighting systems. The choice of electric motors or diesel engines depends on the level of reliability required from the system.

In practice, the GEN fire-fighting booster sets have one electric service pump and one diesel service pump. Point 10.2 of EN 12845 states that for superior or duplicate water supplies, and if more than one pump is installed, no more than one service pump can be driven by the electric motor. This concept means that mixed assemblies, comprising electric or diesel pumps, have to be installed. This does not mean that it is not possible to have two electric pumps, one backing up the other, if the ascertained fire risk is low (single supplies) or if a diesel generator is already incorporated in the system.

SPECIFICATIONS

• Delivery: up to 1,300 m³/h
• Head: up to 150 m
• Power: up to 132 kW
• Maximum operating pressure: 15 bar

L'articolo GEN – Booster sets for firefighting use proviene da FORTEK.

The single mechanical seal CSS-35Q is based on the CSS-35 design equipped with an adapter where is installed a secondary mechanical seal on the air side.

TECHNICAL SPECIFICATIONS

• Mechanical seal design: Single Static Internal PLAN 62
• Process Side Materials: Carbon / SiC /RS-SiC
• Gasket Materials: FKM / EPDM / FFKM
• Mechanical Seal Materials – Environmental Side: Carbon/SiC
• Gasket Materials – Environmental Side: FKM / EPDM / FFKM
• Suitable to PLAN 62

L'articolo CSS-35Q – Single mechanical seal proviene da FORTEK.

• Lining: PP (Polypropylene), PVDF (Polyvinylidene fluoride), PFA (Perfluoroalkoxy)
• End-suction

The UTN-L / UTN-BL (I° frame) pumps have long coupled (UTN-L) and/or close coupled (UTN-BL) execution.

PRODUCT CHARACTERISTICS

• Versatility: Suitable for handling corrosive,aggressive and hazardous liquids (low viscosity, clean or slightly contaminated) in the chemical, petrochemical and Pharma industries, where the need of high safety standards is the first requirement
• Reliability: The pump is equipped with reliable oil lubricated bearing bracket, especially developed to be suitable even under heavy duty service
• Design: UTN range share the same hydraulic design with the UCN series (mechanical seal pumps) which have been developed focusing on chemical industry´s requests

TECHNICAL SPECIFICATIONS

• Shaft seal type Sealless Magnetic Drive
• Design: EN 22858; ISO 2858
• Standard: ISO 5199
• Casing material: PFA Lined – PVDF lined – PP Lined
• Casing partition: Radially split
• Casing Volute: Casing
• Impeller material: PFA Lined – PVDF Lined – PP Lined
• Type of impeller: Closed
• Nozzle position: End Suction
• Type of Execution: Horizontal
• Type of installation:

UTN-L : Long-Coupled
UTN-BL : Close-Coupled

• Pull-out design: UTN-L: Back pull-out
• Heatable: No
• Type of connections: Flanged
• Flange Connections:

UNI 1092-1/ISO 7005-1 PN 16, type B
asolate ANSI 150

• Suction characteristics: Non-priming
• Type of lubrication: UTN-L : Grease
• Drive frequency: 50 Hz / 60 Hz
• Type of drive: Electric motor
• Maximum rated pressure @20°C: PN 16
• Max. permissible fluid temperature:

PP: – 10°C -> -> +70°C
PVDF : -30°C -> +100°C
PFA: – 50°C -> +140°C*

• Maximum head @ 2900 RPM: 70m
• Maximum flow rate @ 2900 RPM: 75 m3/h
• Allowable Medium Viscosity Range: 1cSt – 100cSt
• Maximum drive rating:

UTN-BL: 1.1 kW (motor size 80)-> 18.5 kW (motor size 160)
UTN-L: 0.75 kW (motor size 80)-> 37 kW (motor size 200)

L'articolo UTN-L / UTN-BL (I° frame) – Plastic and fluoroplastic lined magnetic drive horizontal process centrifugal pumps proviene da FORTEK.

• Lining: PP (Polypropylene), PFA (Perfluoroalkoxy)
• End-suction

The UTN-L / UTN-BL (I° frame) pumps have long coupled (UTN-L) and/or close coupled (UTN-BL) execution.

PRODUCT CHARACTERISTICS

• Versatility:  Suitable for handling corrosive,aggressive and hazardous liquids (low viscosity, clean or slightly contaminated) in the chemical, petrochemical and Pharma industries, where the need of high safety standards is the first requirement
• Reliability: The pump is equipped with reliable oil lubricated bearing bracket, especially developed to be suitable even under heavy duty service
• Design: UTN range share the same hydraulic design with the UCN series (mechanical seal pumps) which have been developed focusing on chemical industry´s requests

TECHNICAL SPECIFICATIONS

• Shaft seal type: Sealless Magnetic Drive
• Design: EN 22858; ISO 2858
• Standard: ISO 5199
• Casing material: PFA Lined – PP Lined
• Casing partition: Radially split
• Casing: Volute Casing
• Impeller material: PFA Lined – PP Lined
• Type of impeller: Closed
• Nozzle position: End Suction
• Type of Execution: Horizontal
• Type of installation:

UTN-L : Long-Coupled
UTN-BL : Close-Coupled

• Pull-out design: UTN-L : Back pull-out
• Heatable: No
• Type of connections: Flanged
• Flange Connections:

UNI 1092-1/ISO 7005-1 PN 16, type B
drilling slotted ANSI 150

• Suction characteristics: Non-priming
• Type of lubrication: UTN-L : Grease
• Drive frequency: 50 Hz / 60 Hz
• Type of drive: Electric motor
• Maximum rated pressure @20°C: PN 16
• Max. permissible fluid temperature:

PP: – 10°C -> +70°C
PFA: – 50°C -> +140°C*

• Maximum head @ 2900 RPM: 45m
• Maximum flow rate @ 2900 RPM: 170 m3/h
• Allowable Medium Viscosity Range: 1cSt – 100cSt
• Maximum drive rating:

UTN-BL: 2.2 kW (size 100) -> 37kW (size 200)
UTN-L: 2.2 kW (size 100) -> 37kW (size 200)

• Maximum speed of rotation (RPM): 2900

L'articolo UTN-L / UTN-BL (II° frame) – Plastic and fluoroplastic lined magnetic drive horizontal process centrifugal pumps proviene da FORTEK.

Grec Srl specializes in the selection, design and construction of industrial agitators for liquids, ensuring reliable, economic and personalized solutions, according to the customer’s requirements.

Grec Srl aims to determine the most functional combination between impeller, diameter, speed of rotation and positioning inside the tanks, by selecting the most appropriate constructive solutions.

The Grec agitators have high versatility, and are able to operate in many applications, like:

– Storage tanks for the food industry, chemical and oil

– Processes of water treatment

– Solids mixing and suspension processes in the mining, ceramics and general industry

– Preparation of chemical products through processes of mixing, dispersion and dissolution

– High viscosity applications with the use of axial or radial impellers

L'articolo Top entry mixers with parallel axes cast iron gearbox Grec – AVL series proviene da FORTEK.