HYDROTWIN package has been developed in close co-operation with Bora Blowers, which specialises in manufacturing pressure and vacuum boosters. A sophisticated electronic control for booster operations has been developed to prevent risks of booster seizure in the event that operating conditions exceed allowable working parameters.

TECHNICAL CHARACTERISTICS

• Vacuum rate: High-Medium-Low
• Range mbar: 2-900
• Max pressure bar G: 1.8
• Max flow m³/h: 3500
• Stages nr.: 1-2
• Seal: Mechanical
• Quality assurance: ISO 9001
• Various service liquids

PRODUCT CHARACTERISTICS

• LESS INSTALLED POWER. Reduce to a minimum the absorbed power. In comparison with the traditional systems the saving is considerable and can be in the range of 30 – 40%.
• OVERHEATING PROTECTION. Have total protection against booster seizure that can be caused by overheating that can be caused when its operation is outside the allowed limits. Standard temperature sensors located in the Roots discharge casing area cannot show, in real time, possible elevated temperature of the lobes, these are normally the first components subject to thermal expansion. With the Hydrotwin temperature control is performed by monitoring the compression ratios. Electronic control DVD2 works on the Roots of the problem and not on the consequential causes.
• ROOTS ROTATION FULLY ADJUSTABLE. The Roots RPM are controlled by means of an inverter that receives the signals from a PLC. Hydrotwin ensures plant optimization with best possible efficiency.
• COMPACT DESIGN. The package design has been done studying each component with the target to enable maximum efficiency in the smaller possible space. The overall hydrotwin dimensions give ample installation possibilities.
• EASY PLC ADJUSTMENT. In case of “on the fly” adjustments the PLC (DVD2) installed is user friendly. It takes few seconds to recall and change the most important parameters. This is ensuring the possibility to run the production always at best efficiency.
• PRECISE VACUUM LEVEL SETTABLE. Set and maintain the desired vacuum level, optimizing the quality and minimizing waste in those processes where maintaining the vacuum level stability is very important to get the final product.
• PLUG AND PLAY product. It is ready-to-use. All necessary settings have already been made at our factory. Possible adjustments, if needed, do not require qualified technicians. It takes a minute to change the few main parameters. The operating costs for electronic technicians are completely eliminated. Do not need to be interfaced to other machines.

L'articolo HYDROTWIN / OILTWIN – Pump + Roots Blower vacuum systems with total liquid recirculation proviene da FORTEK.

TECHNICAL CHARACTERISTICS

• Vacuum rate: High-Medium-Low
• Range mbar: 33-900
• Max pressure bar G: 1.8
• Max flow m³/h: 3500
• Stages nr.: 1-2
• Seal: Mechanical
• Total or partial liquid recirculation models
• High efficiency both at high and low vacuum
• Maximum thermal efficiency of the new conception heat exchanger
• Vertical gas discharge with high separation power of the service liquid
• Extreme reliability and stoutness due to the compact skid
• Reduced maintenance and easy accessibility to every component
• Large choice of materials of construction
• Possibility of personalization as a function of plants necessities
• Possibility of construction with 2 pump on single skid

CHARACTERISTICS OF OPERATIONS

The new series HYDROPACK represents the best solution to have compact-size, efficiency and functionality in TOTAL RECIRCULATION liquid ring vacuum systems.

The pump is mounted on a single skid, which is used as separator tank (air/water) and through a heat exchanger, it is possible to maintain a stable and low working temperature.

The level of the service liquid, always in the middle of the pump, pemits a safety start-up and a regular working, even with low vacuum. This new system is also characterised by a long self-sufficiency, due to the high quantity of water that it can contain.
Eventual accessories, like electric valves and/or level gauges, can be easily installed, in order to meet different customers’ plants requests.

PARTIAL RECIRCULATION is also possible, using a more compact skid and removing the internal heat exchanger, with a very low consumption of the service liquid, optimizable according to working necessities.
It is possible to install every pump of our range of production (TRH, TRS, TRM, TRV) up to a maximum capacity and power of 800 m3/h and 30 kW.

For further eventual combinations and information, please contact our Sales Office.

L'articolo HYDROPACK – Compact vacuum systems with total or partial water recirculation proviene da FORTEK.

The vacuum/compression complete package with full recovery of service water HYDROSYS guarantee minimum losses of service liquid.

TECHNICAL CHARACTERISTICS

• Vacuum rate: High-Medium-Low
• Range mbar: 33-900
• Max pressure bar G: 1.8
• Max flow m³/h: 3500
• Stages nr.: 1-2
• Seal: Mechanical
• Variety of materials of construction available
• No contamination of cooling water
• Shut-off vacuum < 10 mbar (with air ejector)
• Turn key and compact packages environmentally safe
• Custom adaptation to meet specific installation and requirements
• Rugged construction with maximum dependability
• Maintenance requirements minimised
• Accessibility for maintenance is maximised

CHARACTERISTICS OF OPERATIONS

The units of HYDROSYS series consist of a liquid-ring vacuum pump of the series TRH, TRS, TRM, TRV, of an air-liquid cyclone separator, of a heat exchanger, all units being mounted on one compact frame. During the operation, the vacuum pump ejects the sucked gas from the delivery port and also part of the service liquid which is present inside it and which must be continuously made up. The air-liquid mixture is delivered to a cylindric tank where the separation occurs: the gas comes out from the upper delivery port of the tank, ready to be sent again to the vacuum pump. During the suction and compression cycle, the vacuum pump transfer all the work carried out under the form of heat to the service liquid, which, of course, before being recycled, shall be cooled down either by means of a heat exchanger (total circuit) or by the supply of fresh liquid from outside (partial circuit).

• The operation by TOTAL RECIRCULATION does not require an external supply of operation liquid if not only the one that is evaporated, if any, or that is ejected together with the discharge gases. The correct dimensioning of the heat exchanger only requires a minimum amount of fresh liquid (usually water) so that the ideal temperature can be maintained for the correct operation of the vacuum pump (please remember that the hotter the operation liquid is, the more loss of suction capacity the pump suffers both in flowrate and in maximum vacuum degree: see the technical information given in our catalogue for vacuum pumps). This system is particularly suitable, when the service liquid or the condensable sucked gases cannot be eliminated outside due to reasons of pollution or to recuperation requirements and cost reasons (see our diagram on page 6).
• The PARTIAL RECIRCULATION operation, instead requires a constant supply of fresh liquid from outside, that is of the same kind as the one circulating inside the unit, since the mixing of the external fresh liquid with the one that is inside the unit keeps the constant temperature of the fresh liquid at the vacuum pump inlet. According to the amount of liquid supplied from outside, the same amount will be eliminated through the discharge located on the center line of the tank (see drawing on page 6). This type of operation is sometimes advantageous if this is required by the flowrate and vacuum characteristics, (for example low vacuum or intermittent operation) or when the service liquid is not polluted and does not create elimination problems. Of course, since a cooling liquid with correct amount and temperature is not available, this remains the only alternative to the total circuit. Several accessories are available to meet particular requirements of plant, of process and of maintenance, and furthermore, it is possible to design particular units, upon request, in co-operation with our Sales Office.

The HYDROSYS series can also be used to work as a compressor up to a maximum pressure of 2 bar, higher than the suction pressure by using tanks and accessories according to ISPESL standards.

L'articolo HYDROSYS – Vacuum systems with total or partial water recirculation proviene da FORTEK.

OILSYS has the capacity to handle gases with suspended particles. The rotating parts have no metal to metal contact and do not require any lubrication. Low noise level and low vibration

TECHNICAL CHARACTERISTICS

• Vacuum rate: High-Medium-Low
• Range mbar: 20-900
• Max pressure bar G: 1.8
• Max flow m³/h: 1600
• Stages nr.: 1-2
• Seal: Mechanical
• Vented air free of oil “smoke” or fumes
• Shut-off vacuum < 10 mbar
• Turn key and compact packages
• Custom adaptation to meet specific installation and requirements
• Rugged construction with maximum dependability
• Maintenance requirements minimised
• Accessibility for maintenance is maximised

ACCESSORIES

• Separator cyclone with collecting tank at pump suction to recover solids and condensables
• Condenser at pump suction and discharge
• Non return valve and gauges
• Water-oil heat exchanger
• Air-oil heat exchanger with oversized passages to minimise fouling

CHARACTERISTICS OF OPERATIONS

OILSYS systems includes a liquid ring vacuum pump from our series TRH, TRS, TRM, TRV, a separator tank which also as a frame, heat exchanger and oil demister to remove oil fumes.

Mineral oil, or equal, is used as service liquid. This fluid has physical properties such that enhances to pump performance and attainable amximun vacuum particularly for vacuum < 100 mbar. The gas handled by the vacuum pump is discharged with some of the service oil into the special frame which acts as gas/oil separator and allows separation from the oil of any evacuated condensables.

The oil is returned to the vacuum pump by means of a circulation pump after being cooled to about 60°C (140° F) through the heat exchanger. The gas is vented after being filtered of any oil through the specially engineered oil demister filter.
A pressur gauge at the filter housing will indicate over pressure when the oil demister filter is plugged and needs replacement. Inspection openings are strategically located at the separator tank-frame to facilitate maintenance and cleaning.

Contrary to rotary vane pumps, these liquid ring vacuum pumps do not require lubrication, therefore contamination of oil by condensables or solid particles is not demaging.

The rugged and reliable construction of the liquid ring vacuum pump is matched by the generously engineered built OILSYS system.

UTILIZATION FIELDS

• brick and ceramics manufacturing
• leather and wood processing
• packaging and food processing
• pneumatic conveying
• poultry evisceration
• plastic and pasta extrusion

L'articolo OILSYS – Vacuum systems with total oil recirculation proviene da FORTEK.

The concept was to create a vacuum system that provided superior vacuum for several applications in a smaller, more maintenance friendly package.

The OILPACK system carries a smaller footprint, runs quieter, and is cooler than most vacuum technologies. In addition, OILPACK is tolerant of some soft solids being sucked into the system.

TECHNICAL SPECIFICATIONS

• Vacuum rate: High-Medium-Low
• Range mbar: 20-900
• Max pressure bar G: 1.8
• Max flow m³/h: 1000
• Stages nr.: 1-2
• Seal: Mechanical
• Better performance at vacuum, flow and absorbed power
• Very compact dimensions
• Simple maintenance
• Limited noise
• Very low working temperature

1. Check valve
2. Vacuum gauge
3. Vacuum regulation valve
4. Anticavitation valve
5. Liquid ring vacuum pump
6. Baseplate
7. Heat exchanger filter
8. Tank
9. Filter replacement gauge
10. Oil thermometer
11. Oil level
12. Heat exchanger

L'articolo OILPACK – Compact vacuum systems with total oil recirculation proviene da FORTEK.

The JUNG HYGHSPIN twin screw pumps are made of stainless steel.

The HYGHSPIN pump is suitable for use with free-flowing products of almost any consistency (whether aqueous, highly viscous, lumpy, fibrous or gaseous) and works with maximum efficiency. This particularly servicing-friendly twin screw pump with its outstandingly high suction performance gently handles all free-flowing products in volumes up to 300 m3 /h. No additional pump for CIP cleaning is required, which offers considerable time and cost savings thanks to lower investment and servicing costs.

APPLICATIONS

• Food manufacturing, e.g. dairy industry, delicatessen products, ketchups and sauces, confectionery and baby food
• Beverage manufacturing, e.g. fruit juices, syrups and concentrates, breweries
• Pharmaceutical industry
• Cosmetics industry, e.g. creams, pastes, lotions
• Chemical industry, e.g. adhesives, solvents, paints and varnishes, plastics And in many other industries where materials with a wide range of viscosities need to be transported.

TECHNICAL SPECIFICATIONS

• Capacity: 30 l/h–300 m³/h (100 l/h–350 m³/h*)
• Delivery pressure: Up to 35 bar
• Suction capacity: NPSHr up to 0.5 m Viscosity 0.5 – 1.000.000 cSt
• Product temperature: –10 to 130 °C, (higher temperatures on request)
• Cleaning temperature: Up to 140 °C
• Sterilisation temperature: Up to 145 °C
• Material for product-contact parts: 1.4404 with 3.1 certificate (other materials on request)
• Elastomers: HNBR and FDA-approved (other elastomers on request)

L'articolo Jung HYGHSPIN twin screw pumps proviene da FORTEK.

Therm-O-Flow 20 offers improved throughput, better process monitoring and reliable, efficient operation.

ADVANTAGES

• Improve process efficiency
  • Keep your production running with automatic electric crossover when using tandem units
• Improve production capability
  • Smaller footprint lets you place unit near the application
  • Capable of melt rates up to 1.3 lb/min (0.6 kg/min)
• Reduce energy costs
  • Inactivity shutoff and temperature setback reduces energy costs
• Supply factory environment initiatives
  • Graco NXT Air Motors operate around 87 decibels while other comparable motors operate up to 103 decibels

Therm-O-Flow 20 – Product features

Intuitive, easy to use controls

• Displays actual and set point temperatures for up to 12 zones per unit
• Material tracking and machine diagnostics can be downloaded to USB
• Provides programmable preventative maintenance schedules
• Languages supported: English, Spanish, German, French, Chinese, Japanese, Portuguese, Italian and Korean

Merkur & NXT Air Motor Technology

• Provides quiet, reliabile, efficient operation
• Proven Graco technology

TECHNICAL SPECIFICATIONS

• Air inlet size: 1/2 npsm(f)
• Air motor sound data: See air motor instruction manual.
• Wetted Parts: carbon steel, brass, chrome, zinc, nickel plating, stainless steel (304, 316, 440, and 17–4 PH), alloy steel, ductile iron, PTFE
• Displacement pump effective are:
  • Merkur and NXT: 8 cm²
  • President: 5.7 cm²
• Volume per cycle
  • Merkur and NXT: 192 cm³
  • President: 62.3 cm³
• Pump cycles per 1 gallon (3.8 liters)
  • Merkur and NXT: 21
  • President: 61
• Ram maximum input pressure
  • Merkur and NXT: 0.85 MPA, 8.5 bar
  • President: 0.8 MPa, 8.3 bar
• Maximum pump operating temperature:
  • Merkur and NXT: 204°C
  • President: 204°C
• Pump fluid outlet size
  • Merkur and NXT: 1 in npt(f)
  • President: 1/2 in npt(f)
• Maximum Fluid Working Pressure
  • Merkur 6.0 in: 15.9 MPa, 159 bar
  • Merkur 7.5 in: 20.7 MPa, 207 bar
  • NXT 6500: 20.7 MPa, 207 bar
  • President 4.25 in: 12.6 MPa, 125 bar
• Maximum Air Input Pressure (Pumps)
  • Merkur 6.0 in: 0.7 MPa, 7 bar
  • Merkur 7.5 in: 0.57 MPa, 5.7 bar
  • NXT 6500: 0.29 MPa, 2.9 bar
  • President 4.25 in: 0.8 MPa, 8.3 bar
• Power Requirements
  • Compressed Air (typical): 25–50 scfm
  • Voltage (as selected):
    220/240 V, 3-phase, 50/60 Hz
    380/400 V, 3-phase, 50/60 Hz
    470/490 V, 3-phase, 50/60 Hz
    575 V, 3-phase, 50/60 Hz
• Peak Consumption (includes drum melt grid, pump, and a 6kVa transformer for the 230 V hoses and accessories)
  • Standard melt grid platen with President pump: 6.4 kVa
  • Standard melt grid platen with Merkur or NXT pump: 8.7 kVa
  • Smooth melt grid platen with President pump: 6.4 kVa
  • Smooth melt grid platen with Merkur or NXT pump: 8.7 kVa

APPLICATIONS

• High-Viscosity Material Transfer
• Bulk Supply System
• Adhesive Bonding
• Fenestration
• Roll Coating
• Curtainwall
• Resin Batch Blending
• Prepreg Supply
• Wood Finishing – Bonding and Laminating

INDUSTRIES

• Automotive Trim and General Assembly
• Automotive Composites
• Solar Energy
• Furniture Finishing / Manufacturing
• Bookbinding
• RVs and Trailers
• Wood Lamination

L'articolo Therm-O-Flow 20 – Bulk Hot Melt systems proviene da FORTEK.

The Therm-O-Flow 200 is an industrial bulk hot melt glue machine system that outperforms the competition with great production throughput, better process monitoring and reliable, efficient operation.

Improve process efficiency

• Keep your production runnnig with automatic electric crossover when using tandem units

Improve production capabililty

• Highest throughout capability in the industry when tested and compared to leading competitor using PSA and butyl hot melt adhesives
• Capable of melt rates up to 11 lb/min (5 kg/min)

Reduce energy costs

• Inactivity shutoff and temperature setback reduces energy costs

Supply factory environment initiatives

• Graco NXT Air Motors operate around 87 decibels while other comparable motors operate up to 103 decibels

Therm-O-Flow 200 – Product features

Intuitive, easy to use controls

• Displays actual and set point temperatures for up to 12 zones per unit
• Material tracking and machine diagnostics can be downloaded to USB
• Provides programmable preventative maintenance schedules
• Languages supported: English, Spanish, German, French, Chinese, Japanese, Portuguese, Italian and Korean

Merkur & NXT Air Motor Technology

• Provides quiet, reliable efficient operation
• Proven Graco technology

TECHNICAL SPECIFICATIONS

• Displacement Pump Effective Area: 1.24 sq in
• Volume per Cycle: 11.7 cu in
• Pump Cycles: 21/1 gal
• Maximum Air Input Pressure (Ram): 125 psi
• Maximum Pump Operating Temperature: 400 °F
• Air Inlet Size: 1/2 npsm(f)
• Pump Fluid Outlet Size: 1 in. npt(f)
• Wetted Parts: Carbon steel; brass; chrome, zinc, and nickel plating; 304, 316, 440, and 17–4 PH grades of stainless steel; alloy steel; ductile iron; PTFE
• Weight: 1200 lb
• Displacement Pump Weight: 81 lb
• Maximum fluid working pressure
  • NXT 2200: 2300 psi
  • NXT 3400: 3000 psi
  • NXT 6500: 3000 psi
• Maximum air input pressure (pumps):
  • NXT 2200: 100 psi
  • NXT 3400: 82 psi
  • NXT 6500: 43 psi
• Air Motor Piston Effective Area
  • NXT 2200: 28.3 sq in
  • NXT 3400: 44.2 sq in
  • NXT 6500: 84.5 sq in
• Instruction Manuals
  • Heated Hoses: 309160
  • Wiper Kits: 309196
  • Bare Displacement Pump Lower: 308570
  • 6.5 in. (165 mm) Global Ram Module: 310523
• Power Requirements
  • Compressed Air: 25–50 scfm (typical)
  • Voltage (as selected)

220/240 V, 3-phase, 50/60 Hz

380/400 V, 3-phase, 50/60 Hz

470/490 V, 3-phase, 50/60 Hz

575 V, 3-phase, 50/60 Hz

• Peak Consumption
  • With standard melt grid: 24.5 kVa
  • With mega-Flo melt grid: 27.5 kVa
  • With smooth melt grid: 24.5 kVa

APPLICATIONS

• High-Viscosity Material Transfer
• Bulk Supply System
• Adhesive Bonding
• Fenestration
• Roll Coating
• Curtainwall
• Resin Batch Blending
• Resin Saturation
• Wood Finishing – Bonding and Laminating

INDUSTRIES

• Automotive Trim and General Assembly
• Automotive Composites
• Solar Energy
• Furniture Finishing / Manufacturing

L'articolo Therm-O-Flow 200 – Bulk Hot Melt systems proviene da FORTEK.

The Therm-O-Flow guns are manual and automatic dispense applicators for applying hot melt materials.

Perfect for high pressure, high flow sealant and adhesive applications, Therm-O-Flow Guns are available with electric switches so they can be used in conjunction with automated equipment.

Therm-O-Flow guns – Product features

• Precise temperature control from PID control panel
• Piston-actuated ball and seat design for positive shut off
• Light trigger pull
• Rugged all metal construction

The most advanced technology on the market

With throughput capability 200% better than the leading competitor, Therm-O-Flow® bulk hot melt systems from Graco outperform the competition time after time and provide the best performing industrial bulk melt systems on the market. Therm-O-Flow’s advanced temperature control capability virtually eliminates overheated material, resulting in better adhesive quality and reduced rework due to degraded material. Graco offers a complete line of Therm-O-Flow bulk hot melt systems and “point of use” melt systems – each can be configured to fit your specific application.

ADVANTAGES

• Improve process efficiency
  • Keep your production runnnig with automatic electric crossover when using tandem units
• Improve production capabililty
  • Highest throughout capability in the industry when tested and compared to leading competitor using PSA and butyl hot melt adhesives
  • Capable of melt rates up to 11 lb/min (5 kg/min)
• Reduce energy costs
  • Inactivity shutoff and temperature setback reduces energy costs
• Supply factory environment initiatives
  • Graco NXT Air Motors operate around 87 decibels while other comparable motors operate up to 103 decibels

TECHNICAL SPECIFICATIONS

• Maximum operating temperature: 400°F
• Maximum fluid working pressure: 5000 psi
• Outlet port size: 5/8-18 UNF-2B
• Inlet port size on gun housing: 7/8-14 UNF- 2B
• Inlet port size on fluid swivel: 7/8-14 JIC(m)
• Voltage: 230/240 Vac
• Wattage: 120 W
• Resistance temperature detector(platinum RTD; 0.00385 ohm/ohm/°C): 108.2 ohms @ 70°F
• Heater resistance
  • individually: 890 ohms, +/- 70 ohms
  • wired in parallel: 445 ohms, +/- 35ohms
• Weight: without swivel: 2.7 lb; with swivel: 3.4 lb / 1.5 kg
• Dimensions
  • Height: 191 mm
  • Width: 76 mm
  • Length:
  • Models 249514 and 249515: 229 mm
  • Models 249512 and 249513: 267 mm
  • Models 297273 and 297274: 292 mm
• Wetted parts: Aluminum, fluorocarbon rubber, stainless steel, PTFE, carbon steel, brass

MATERIALS

• Structural Adhesives
• Polymers

APPLICATIONS

• Adhesive Bonding
• Fenestration
• Wood Finishing – Bonding and Laminating

INDUSTRIES

• Automotive Trim and General Assembly
• Furniture Finishing / Manufacturing

L'articolo Therm-O-Flow Guns – Dispense applicators for hot melt materials proviene da FORTEK.

The ambient supply systems are bulk unloaders for ambient sealants, adhesives and other medium to high-viscosity materials.

Graco supply systems reliably deliver one-component sealants, adhesives and other medium to high-viscosity materials from pails or drums to metering and dispensing systems.

For magnadrums & tote drums up to 1200 liter (300 gal)

The Uni-Drum supply system evacuates 300 gallon (1200 liter) magnadrums and other tote drums of the same size and capacity.

• Pumps and transfers highly viscous materials from bulk drums with maximum efficiency
• Built to work with other high pressure equipment to optimize material use

For large drums up to 200 liter (55 gal)

• Graco D200 – For high-volume in-plant applications
• Graco D200s – For heavy-duty, high-volume applications of high-viscosity materials. Provides more down-force for difficult-to-move materials

For pails up to 60 liter (16-gal)

For 20, 30 and 60 liter (5, 7, and 16-gal) pail sizes. Provides the same proven technologies as the larger systems, but with small NXT Air Motors.

• Graco L20c – A lightweight, elevator ram on a cart
• ”  ” ”   S20 – For low-volume applications of medium to high-viscosity materials
• Graco S20c – Same as the S20, but includes a cart
• ”  ” ”   D60 – Provides higher down-force and 60-liter pail capacity

For 1 quart (0.95l) or 1 gallon (3.79l) containers

The Graco DynaMite Pump utilizes the NXT air motor to provide the power necessary to move viscous materials from small containers.

• Manual or automatic valve applications
• Ideal for small manufacturing workcells and industrial workbench applications
• 
Typical fluids handled:
  • Sealants and Adhesives
  • Potting and Heatsink Compounds
  • 
Encapsulants
  • Grease
  • 
Inks and Colorants

TECHNICAL SPECIFICATIONS

• Max air input pressure (supply system) / Air inlet size
  • L20c – 2 in elevator, 5 gal (20 l): 100 psi / 1/2 npsm(f)
  • S20 – 3 in single post, 5 gal (20 l): 125 psi / 1/2 npt(f)
  • D60 – 3 in dual post, 16 gal (60 l), 5 gal. (20 l), 30 gal: 150 psi / 3/4 npt(f)
  • D200 – 3 in dual post, 55 gal (200 l), 30 gal (115 l),16 gal (60 l), 8 gal (30 l), 5 gal (20 l): 150 psi / 3/4 npt(f)
  • D200s – 6.5 in dual post, 55 gal (200 l), 30 gal (115 l): 125 psi / 3/4 npt(f)
• Max fluid, air working pressure. and weight (displacement pump):
  For Check-Mate pump packages, see manual 312376. For Dura-Flo pump packages, see manuals 311826, 311828, 311833.
• Ambient operating temperature range (supply system): 32-120°F
• Sound data: See separate air motor manual.
• External power supply requirements (DatraTrak)
  • AC power units: 100-240 Vac, 50/60 Hz, single phase, 1.2 amps max
  • DC power units: 24 Vdc, 1.2 amps max draw

MATERIALS

• Contact Cements
• Sealants
• Mastics
• Epoxy Sealants and Adhesives
• Silicones
• Dow Corning® 983 Silicone

APPLICATIONS

• Bulk Supply System
• Medium-Viscosity Material Transfer
• Adhesive Bonding
• Automotive Hem-Flange Bonding
• Roll Coating
• Curtainwall
• Thermal Management
• Composites Open Molding
• Resin Batch Blending
• Resin Saturation
• Prepreg Supply

INDUSTRIES

• Automotive Trim and General Assembly
• Powertrain
• Body Shop Sealing
• Automotive Electronics / Under the Hood
• Automotive Composites
• Wind Power – Blades
• Chemical Manufacturing
• Electronics Manufacturing
• Furniture Finishing / Manufacturing

L'articolo Ambient supply systems for sealants and adhesives proviene da FORTEK.